Large surface for hold down, mostly
Combined surface for flatting and spraying
Small surface for spot treatments
Combined surface use dangerous liquids and/or inflammable solvents
low suction force
middle suction force
vacuum
middle suction force
high airflow
high airflow
low airflow
high airflow
ELECTRIC
ELECTRIC
PNEUMATIC
WATER-POWERED
CENTRIFUGAL FANS or EXHAUSTERS
RADIAL PUMP or ROTARY VANE PUMPS
MULTI STAGE EJECTOR
WATER-JET EJECTOR
The JEZET VACUUM TABLE-TOP VTT-0404Po is constructed of anodized softline profiles
JZ800 with a inserted shaped base-plate, a rigid heavy duty support grid all made
of aluminum to restrain even a higher vacuum (maximum of -90 kPa abs. = 125 mBar.
= 27 inch Hg) and a porous working surface made of white Polyethylene permitting
a maximum mesh of 28% per square meter. The table top rear side is provided with
an aluminum suction pipe to be connected with a suction or vacuum unit. The size
of the useful working surface is W x D 400 X 400 mm. outside dimensions 440 x 440
mm. height 40 mm.
The JEZET VACUUM TABLE-TOP VTT-1909St is constructed of anodized softline profiles
JZ800 with a inserted shaped base-plate, a rigid heavy duty support grid all made
of aluminum to restrain even a higher vacuum (maximum of -90 kPa abs. = 125 mBar.
= 27 inch Hg) and a perforated working surface made of hard wearing, easy to clean
non corrosive, stainless steel permitting a maximum mesh of 35% per square meter.
The table top rear side is provided with an aluminum suction pipe to be connected
with a suction or vacuum unit.
The size of the useful working surface is W x D 1950 X 950 mm. outside dimensions
2000 x 1000 mm. height 80 mm.
The JEZET VACUUM TABLE-TOP VTT-1809St + SPP is constructed of anodized softline profiles
JZ800 with a inserted shaped base-plate, a rigid heavy duty support grid all made
of aluminum to restrain even a higher vacuum (maximum of -90 kPa abs. = 125 mBar.
= 27 inch Hg) and a perforated working surface made of hard wearing, easy to clean
non corrosive, stainless steel permitting a maximum mesh of 35% per square meter.
The table top is inserted in to an existing cabinet and the bottom is provided with
an aluminum suction pipe, connected with the inlet of the separate TRAPTANK and on
the outlet directly fitted the adjustable PNEUMATIC VACUUM UNIT. The size of the
useful working surface is W x D = 1800 X 900 mm.
The JEZET VACUUM TABLE-TOP VTT-1210St + SEZ is constructed of anodized softline profiles
JZ800 with a inserted shaped base-plate, a rigid heavy duty support grid all made
of aluminum to restrain even a higher vacuum (maximum of -90 kPa abs. = 125 mBar.
= 27 inch Hg) and a perforated working surface made of hard wearing, easy to clean
non corrosive, stainless steel permitting a maximum mesh of 35% per square meter.
The table top rear side is provided with a triple polyethylene suction pipe connected
with the inlet of the separate TRAPTANK and the outlet by means of a flexible hose
with an INDUSTRIAL VACUUM CLEANER.
The size of the useful working surface is W x D 1200 X 1000 mm. outside dimensions
1240 x 1040 mm. height 80 mm.
JEZET VACUUM TABLE SYSTEM VTTFwSPP-0906St (simple execution without compressor) built-up
of the following components: a SUPPORT FRAME on 4 castors with brakes with on top
a VACUUM TABLE-TOP provided with a perforated working surface of stainless steel.
The table top SUCTION PIPE is connected with the inlet of the TRAPTANK and the outlet
by means of a flexible hose to the adjustable PNEUMATIC VACUUM UNIT. Both fixed on
the base of the support frame. A quick release coupling connection for a spray gun.
Working; suction; area
Area height
Outside measures
Compressed air consumption maximum
Exhaust air outlet
Noise level maximum
Colour
Weight
950 x 600 mm
800 mm
W x D =1000 x 640 mm
150 litres per minute at 6 Bar
Ø 75 mm flexible synthetic hose 5 meters
with operating vacuum device 55 dB. Otherwise 45 dB
Silver and Black
approximately 43 kg
JEZET VACUUM TABLE SYSTEM VTTFwSPPHy-1308St built-up of the following components:
a SUPPORT FRAME on 4 castors with brakes with on top a VACUUM TABLE-TOP provided
with a perforated working surface of stainless steel. The table top SUCTION PIPE
is connected with the inlet of the TRAPTANK and the outlet by means of a flexible
hose to the adjustable PNEUMATIC VACUUM UNIT. Both and the Hydrovane COMPRESSOR for
the air supply, fixed on the support frame base. A quick release coupling connection
for a spray gun.
Usable Surface Vacuumtable
Working height
Outside measures
Electrical connection
Maximum power consumption of the Compressor
Exhaust connection
Noise level with compressor running
Total weight
Colour
1300 x 800 mm
800 mm
W x D = 1340x 840 mm
Euro connector with flexible cable of 10 m single phase - neutral and Earth
1,5 k Watt 16 Ampere 230 Volt – 50 Hz
flexible hose of Ø 75 mm 5 meters
maximum of 67 dB otherwise 45 dB
approximately 80 kg
Silver and black
JEZET SUCTION TABLE VTT2FwPh45º-1809St pneumatic stepless adjustable in angle to
45º built-up of the following components: 2 SUPPORT FRAMES of aluminum profile plus
plating of Trespa on 4 castors with FRONT BRAKES with on top a VACUUM TABLE-TOP of
anodized softline profiles JZ800 with a inserted shaped base-plate, a rigid heavy
duty support grid all made of aluminum to restrain even a higher vacuum (maximum
of -90 kPa abs. = 125 mBar. = 27 inch Hg) and a perforated working surface made
of hard wearing, easy to clean non corrosive, stainless steel permitting a maximum
mesh of 35% per square meter. The table top is pneumatically stepless adjustable
in angle to 45º vertical.
The table top bottom is provided with an aluminum suction pipe to be connected by
means of a flexible hose to with a suction or vacuum unit.
Usable Surface Vacuumtable
Working height
Outside dimensions
Suction connection
Total weight
Colour
angle to 45º
without compressor
W x L = 1800 x 950 mm
800 mm
W x D = 1840x 1000 mm
flexible hose of Ø 75 mm 5 meters
approximately 67 kg
Silver and black
JEZET SUCTION TABLE VTTFwSPPMh45º-1409St manually stepless adjustable in angle to
45º built-up of the following components: SUPPORT FRAME of aluminum profile plus
plating on 4 castors with brakes with on top a VACUUM TABLE-TOP of anodized softline
profiles JZ800 with a inserted shaped base-plate, a rigid heavy duty support grid
all made of aluminum to restrain even a higher vacuum (maximum of -90 kPa abs. =
125 mBar. = 27 inch Hg) and a perforated working surface made of hard wearing, easy
to clean non corrosive, stainless steel permitting a maximum mesh of 35% per square
meter. The table top is manually stepless adjustable in angle to 45º vertical.
The table top SUCTION PIPE is connected with the inlet of the TRAPTANK and the outlet
by means of a flexible hose to the adjustable PNEUMATIC VACUUM UNIT. Both fixed on
the base of the support frame. A quick release coupling connection for a spray gun.
Usable Surface Vacuumtable
Working height
Outside dimensions
Compressed air consumption maximum
Exhaust air outlet
Noise level maximum
Colour
Weight
to 45º
without compressor
separate compressor 2,2 kW
W x L = 1470 x 970 mm
800 mm
W x D = 1600x 1000 mm
350 litres per minute at 6 Bar
Ø 75 mm flexible synthetic hose 5 meters
with operating vacuum device 55 dB. Otherwise 45 dB
Silver and Black
approximately 80 kg
JEZET VACUUM TABLE SYSTEM VTTFwSEP-1308St built-up of the following components: a
SUPPORT FRAME on 4 castors with brakes with on top a VACUUM TABLE-TOP provided with
a perforated working surface of stainless steel. The table top SUCTION PIPE is connected
with the inlet of the TRAPTANK and the outlet by means of a flexible hose to the
adjustable ELECTRIC SUCTION UNIT. Both fixed on the support frame base.
Usable Surface Vacuumtable
Working height
Outside dimensions
Electrical connection
Maximum power consumption
Compressed air consumption maximum
Exhaust connection
Noise level with compressor running
Weight
Colour
1300 x 800 mm
800 mm
W x D = 1340x 840 mm
Euro connector with flexible cable of 10 m single phase - neutral and Earth
2,2 k Watt 16 Ampere 230 Volt – 50 Hz
50 litres per minute at 6 Bar
flexible hose of Ø 75 mm 5 meters
maximum of 62 dB otherwise 45 dB
approximately 75 kg
Silver and black
JEZET WORK SUCTION TABLE FOR PROCESSING OF SOLVENTS VTTFwSs-0505St consisting of:
a TABLETOP of a porous work surface of STAINLESS STEEL on a SUPPORT FRAME of Aluminum
profiles on 4 castors of which the front have brakes. On the bottom-mounted base
plate is mounted a SPECIAL LARGE TRAPTANK to be connected with a flexible hose to
any new or existing suction device.
With optic level control, water supply connection with valve and drain tap.
Usable Surface Suctiontable
Exhaust connection
Total weight
Colour
B x D = 500 x 500 mm
flexible hose of Ø 75 mm 5 meters
approximately 45 kg
Silver and black
JEZET VACUUM TABLE SYSTEM VTTFwHdPSPPHy-1208St built-up of the following components:
a SUPPORT FRAME on 4 castors with brakes with on top a VACUUM TABLE-TOP provided
with a perforated working surface of stainless steel. The table top SUCTION PIPE
is connected with the inlet of the TRAPTANK and the outlet by means of a flexible
hose to the adjustable PNEUMATIC VACUUM UNIT. Both and the Hydrovane COMPRESSOR for
the air supply, fixed on the support frame base. A quick release coupling connection
for a spray gun. Further provided with a HUMIDIFICATION DOME plus connections with
a pneumatically up and down operation.
Usable Surface Vacuumtable
Working height
Outside dimensions
Electrical connection
Maximum power consumption of the Compressor
Exhaust connection
Noise level with compressor running
Total weight
Colour
1200 x 800 mm
800 mm
W x D = 1240x 840 mm
Euro connector with flexible cable of 10 m single phase - neutral and Earth
1,5 k Watt 16 Ampere 230 Volt – 50 Hz
flexible hose of Ø 75 mm 5 meters
maximum of 62 dB otherwise 45 dB
approximately 90 kg
Silver and black
JEZET VACUUM TABLE SYSTEM VTTFwHdPSPPP-1308St built-up of the following components:
a SUPPORT FRAME on 4 castors with brakes with on top a VACUUM TABLE-TOP provided
with a perforated working surface of stainless steel. The table top SUCTION PIPE
is connected with the inlet of the TRAPTANK and the outlet by means of a flexible
hose to the adjustable PNEUMATIC VACUUM UNIT. Both and the Hydrovane COMPRESSOR for
the air supply, fixed on the support frame base. A quick release coupling connection
for a spray gun. Further provided with a HUMIDIFICATION DOME plus connections with
a pneumatically up and down operation.
Usable Surface Vacuumtable
Working height
Outside dimensions
Electrical connection
Maximum power consumption
Compressed air consumption maximum
Exhaust connection
Noise level with compressor running
Total weight
Colour
1300 x 800 mm
800 mm
W x D = 1340x 840 mm
Euro connector with flexible cable of 10 m single phase - neutral and Earth
2,2 k Watt 16 Ampere 230 Volt – 50 Hz
350 litres per minute at 6 Bar
flexible hose of Ø 75 mm 5 meters
maximum of 62 dB otherwise 45 dB
approximately 90 kg
Silver and black
Picture available in January 2012
JEZET VACUUM TABLE SYSTEM VTTFwHdPSPPHy-1308St built-up of the following components:
a SUPPORT FRAME on 4 castors with brakes with on top a VACUUM TABLE-TOP provided
with a perforated working surface of stainless steel. The table top SUCTION PIPE
is connected with the inlet of the TRAPTANK and the outlet by means of a flexible
hose to a triple station one to the adjustable ELECTRIC SUCTION and the other to
the adjustable PNEUMATIC VACUUM UNIT. Both and the Hydrovane COMPRESSOR for the
air supply, fixed on the support frame base. Further provided with a HUMIDIFICATION
DOME plus connections with a pneumatically up and down operation and an ULTRASONIC
HUMIDIFYER and a separate BOOKWEDGE. A quick release coupling connection for a spray
gun.
Usable Surface Vacuumtable
Working height
Outside dimensions
Electrical connection
Maximum power consumption of the Compressor
Exhaust connection
Noise level with compressor running
Total weight
Colour
1300 x 800 mm
800 mm
W x D = 1340x 840 mm
Euro connector with flexible cable of 10 m single phase - neutral and Earth
1,5 k Watt 16 Ampere 230 Volt – 50 Hz
flexible hose of Ø 75 mm 5 meters
maximum of 62 dB otherwise 45 dB
approximately 95 kg
Silver and black
JEZET VACUUM TABLE SYSTEM VTTFwHdPSPP-1308St with 2 extra tiltable WORKTABLES built-up
of the following components: a SUPPORT FRAME on 4 castors with brakes with on top
a VACUUM TABLE-TOP provided with a perforated working surface of stainless steel.
The table top SUCTION PIPE is connected with the inlet of the TRAPTANK and the outlet
by means of a flexible hose to the adjustable PNEUMATIC VACUUM UNIT. Both fixed on
the support frame base. Further provided with a HUMIDIFICATION DOME plus connections
with a pneumatically up and down operation and an ULTRASONIC HUMIDIFYER commanded
by a HYGROSTAT and on the sides 2 extra tiltable WORKTABLES.
Usable Surface Vacuumtable / with tables
Working height
Outside dimensions
Electrical connection
Maximum power consumption
Compressed air consumption maximum
Exhaust connection
Noise level with compressor running
Total weight
Colour
1300 x 800 mm / 2700 x 800 mm
800 mm
W x D = 2740x 840 mm
Euro connector with flexible cable of 10 m single phase - neutral and Earth
0,85 k Watt 16 Ampere 230 Volt – 50 Hz
350 litres per minute at 6 Bar
flexible hose of Ø 75 mm 5 meters
maximum of 62 dB otherwise 45 dB
approximately 65 kg
Silver and black
JEZET VACUUMTABLE VTTFwHdPSPP -1308St+ SEPARATE LIGHT TABLE LTT-0806 built-up of
the following components: a SUPPORT FRAME on 4 castors with brakes with on top a
VACUUM TABLE-TOP provided with a perforated working surface of stainless steel. The
table top SUCTION PIPE is connected with the inlet of the TRAPTANK and the outlet
by means of a flexible hose to the adjustable PNEUMATIC VACUUM UNIT, Further provided
with a HUMIDIFICATION DOME plus connections with a pneumatically up and down operation
and an ULTRASONIC HUMIDIFYER commanded by a HYGROSTAT, a CONTROLEPANEL with SPRAY
GUN,
The LIGHT TABLE-TOP is executed with a working surface is made of opal laminated
tempered glass. The light compartment contains MULTY LEDS of the COLD light 5.000
Lux. Day-light colour. On-off switch and DIMM switch
Usable Surface Vacuumtable / illuminated surface
Working height
Outside dimensions
Electrical connection
Maximum power consumption
Compressed air consumption maximum
Exhaust connection
Noise level
Total weight
Colour
1300 x 800 mm / 800 x 600 mm
800 mm
W x D = 1900 x 840 mm
Euro connector with flexible cable of 10 m single phase - neutral and Earth
1,0 k Watt 16 Ampere 230 Volt – 50 Hz
350 litres per minute at 6 Bar
flexible hose of Ø 75 mm 10 meters
During suction maximum noise level of 60 dB otherwise 45 dB
approximately 85 kg
Silver and black
JEZET VACUUMTABLE SYSTEM VTTFwHdESEP-1308St + LIGHT/SUCTION TABLE LVTT-0806 built-up
of the following components: a SUPPORT FRAME on 4 castors with brakes with on top
a VACUUM TABLE-TOP provided with a perforated working surface of stainless steel.
The table top SUCTION PIPE is connected with the inlet of the TRAPTANK and the outlet
by means of a flexible hose to a triple station with one connection and valve to
the adjustable ELECTRIC SUCTION UNIT and the other connection and valve to the LIGHT/SUCTION
TABLE-TOP. Further provided with a HUMIDIFICATION DOME plus connections with a electrically
up and down operation and an ULTRASONIC HUMIDIFYER commanded by a HYGROSTAT, a CONTROLEPANEL
with SPRAY GUN,
The LIGHT/SUCTION TABLE-TOP is executed of a suction compartment with working surface
made of WHITE POLYETHELENE and a light compartment with MULTY power LEDS of the COLD
light 5.000 Lux. Day-light colour. On-off switch and DIMM switch
Usable Surface Vacuumtable / illuminated Suction surface
Working height
Outside dimensions
Electrical connection
Maximum power consumption
Exhaust connection
Noise level
Total weight
Colour
AND PLAY)
1300 x 800 mm / 800 x 600 mm
800 mm
W x D = 1900 x 800 mm
Euro connector with flexible cable of 10 m single phase - neutral and Earth
2,2 k Watt 16 Ampere 230 Volt – 50 Hz
flexible hose of Ø 75 mm 10 meters
During suction maximum noise level of 60 dB otherwise 45 dB
approximately 80 kg
Silver and black
JEZET ILLUMINATED SUCTION TABLE LVTTFwSEP-1510Po built-up of the following components:
a SUPPORT FRAME on 4 castors with brakes with on top a LIGHT SUCTION TABLE/WALL is
composed in two compartments: 1 for vacuum and 1 for light. The vacuum compartment
made of transparent polycarbonate and a rigid support platform The working surface
is made of hard wearing, easy to clean non corrosive, WHITE POLYETHELENE. The light
compartment is made of an Aluminum base plate and a MULTY LEDS unit of high Intensity
with the COLD light 5.000 Lux. Day-light colour. The table top SUCTION PIPE is connected
with the inlet of the TRAPTANK and the outlet by means of a flexible hose to the
adjustable ELECTRIC SUCTION UNIT. Both fixed on the support frame base.
Usable illuminated surface
Working height
Outside dimensions
Electrical connection
Maximum power consumption
Exhaust connection
Noise level
Total weight
Colour
1000 x 700 mm
800 mm
W x D = 1080 x 780 mm
Euro connector with flexible cable of 10 m single phase - neutral and Earth
1,5 k Watt 16 Ampere 230 Volt – 50 Hz
flexible hose of Ø 75 mm 10 meters
During suction maximum noise level of 60 dB otherwise 45 dB
approximately 45 kg
Silver and black
JEZET ILLUMINATED SUCTION TABLE and WALL LVTWFwSEPHeKe90º-1510Po built up out of
the following components: The LIGHT SUCTION TABLE/WALL is composed in two compartments:
1 for vacuum and 1 for light. The vacuum compartment made of transparent polycarbonate
and a rigid support platform The working surface is made of hard wearing, easy to
clean non corrosive, WHITE POLYETHELENE. The light compartment is made of an Aluminum
base plate and a MULTY LEDS unit of high Intensity with the COLD light 5.000 Lux.
Day-light colour. The size of the useful working surface of the table-top W x D 1.500
X 1.200 mm. The SUPPORT FRAME is constructed of a base frame provided with four castors
with brakes. Mounted on the frame 2 linear actuators for stepless movement from up
to 1150 and down to 750 mm. On the actuators is mounted a top frame to support the
LIGHT VACUUM TABLE/SUCTION WALL and enables it to tilt from HORIZONTAL to VERTICAL
by means of 4 hinges on the front and a linear actuator. Further on the base frame
the ELECTRIC SUCTION DEVICE, PNEUMATIC VACUUM DEVICE, TRAPTANK, CONTROLEPANEL, CONTROLEBOX
and connections.
Usable Surface for/as Illumination, Work; Suction, Vacuum, etc.
Working height variable / Step less tilting
Outside dimensions
Electrical connection
Maximum power consumption
Pneumatic connection
Pneumatic consumption
Exhaust connection
Noise level
Total weight
Colour
1500 x 1000 mm
750 to 1100 mm. / between 0º to 90º
W x D = 1600x 1200 mm
Euro connector with flexible cable of 10 m single phase - neutral and Earth
2.2 k Watt 16 Ampere 230 Volt – 50 H.z
quick release coupling and flexible hose of Ø 9 mm of 6 metres
350 litres per minute max at 10 Bar
flexible hose of Ø 75 mm 10 meters
During suction maximum noise level of 60 dB otherwise 45 dB
approximately 150 kg
Silver and black
JEZET VACUUM TABLE VTTFwHdPSEPPPHeKe45º-1310Po adjustable in Height and Angle + HUMIDIFICATION
unit built up out of the following components: VACUUM TABLE-TOP is constructed of
aluminum profiles and POLYETHELENE WORKSURFACE (exchangeable with a Stainless steel
perforated work surface) and mounted on the TOP SUPPORT FRAME by means of 4 hinges
at the front and an electric actuator permitting the vacuum table top a step less
tilting between 0º to 45º The top frame is mounted on a one aluminum lifting-column
with a step less height adjustment
The column is fixed on the BASE FRAME mobile on 4 castors with brakes. On the base
frame are also fixed the MOISTURE OR LIQUID TRAPTANK (far better and less dangerous
than an activated carbon filter, The connecting system, The ELECTRIC MEDIUM PRESSURE
SUCTION UNIT a suction level of -40kPa on a big surface. The PNEUMATIC VACUUM UNIT
a suction level of - 80kPa , The ULTRASONIC HUMIDIFER.
The TURNABLE CONTROLEPANEL is built on the front of the table top and executed with
24 Volts safety current and the necessary equipment
The higher HUMIDIFICATION DOME is made of aluminum profiles and transparent POLYCARBONATE
and mounted on to the table top by means of 2 hinges and also provided with a HYGROSTAT
mounted in the dome of the Vacuum table to control the ULTRASONIC HUMIDIFER. Furthermore
executed with a LOW PRESSURE SPRAY GUN with flexible hose and quick release coupling
Working; suction; area
Area height and tilting
Outside dimensions
Electricity consumption maximum
Exhaust air outlet
Noise level maximum
Total weight
Colour
1300 x 1000 mm
800 to 1100 mm. and 0 to 45º
W x D x H =1380 x 900 x 1500 mm
2,2 k Watt 240V – 50hz 1 Phase
Ø 75 mm flexible synthetic hose 5 meters
with operating suction device 60 dB. Otherwise 45 dB
approximately 175 kg
Silver and black
The JEZET SUCTION BOOK WEDGE VBW-0302StS is constructed of a perforated working surface
made of hard wearing, easy to clean non corrosive, stainless steel permitting a maximum
mesh of 35% per square meter and a closed stainless steel base. The BOOK WEDGE rear
side is formed by a stainless steel suction pipe which can be left or right connected
with a suction unit or vacuum cleaner.
The size of the useful working surface is W x D 300 X 240 mm. outside dimensions
360 x 260 mm. height 3 to 35 mm
The JEZET ILLUMINATED SUCTION BOOK WEDGE LVBW-0302Po is constructed of a porous working
surface made of white Polyethylene permitting a maximum mesh of 28% per square meter.
and a closed base made of white Polyethylene. On both sides at the rear end are suction
pipes which can be connected with a suction unit or vacuum cleaner. The BOOK WEDGE
rear side is formed by a transparent polycarbonate plate and can be provided with
a MULTY LEDS unit of high Intensity with the COLD light 5.000 Lux. Day-light colour.
Or an already existing light unit of low temperature. No halogen to hot
The size of the useful working surface is W x D 300 X 240 mm. outside dimensions
360 x 260 mm. height 7 to 40 mm.
The treatments can be divided on to 3 different surface sizes and 3 vacuum generations
each with its special qualities as: usability, capability, adaptability, performance
and advantages.
Large surface for hold down, mostly
Combined surface for flatting and spraying
Small surface for spot treatments
Combined surface use dangerous liquids and/or inflammable solvents
low suction force
middle suction force
vacuum
middle suction force
high airflow
high airflow
low airflow
high airflow
ELECTRIC
ELECTRIC
PNEUMATIC
WATER-POWERED
CENTRIFUGAL FANS or EXHAUSTERS
RADIAL PUMP or ROTARY VANE PUMPS
MULTI STAGE EJECTOR
WATER-JET EJECTOR
EXECUTION
size(small/medium/big) working-height(standing/seated);
treatment-surface
material(Aluminum/Stainless steel/Plastic/Brass)
strength(vacuum/suction force) stability(rigid
profile frame) corrosion
durability(treatment-liquid/solvent resistance)
mobility(on wheels/steady) fixed
or tiltable(manually, pneumatic) weight(light
weight construction and material)
floor(space, load) restoration-workshop
(building, access, doors) design (compact; ergonomic
and easy to clean)
TREATMENTS
accessibility(one side or on all sides) treatments
with inflammable solvents (cooled surface, cold air supply, traptank, cooling labyrinth,
explosion proof suction necessary)
humidification(polycarbonate dome and humidifier) readings(vacuum-gauge,
pressure-gauge, thermometer, hygrostat)
conditioned air supply(filter and conditioner) additional
connections( hygrostat, spray-gun, compressed air)
hot lining (heated surface or heated air supply) adapting
of/to existing components(suction/vacuum unit, table, under frame, extraction, etc)
The ADVANTAGES of the JEZET VACUUM TABLE SYSTEMS
one component to total set-up or only for a particular treatment (custom made) adaptable
to or integration into already existing components or systems (special requests)
All inert materials and components handy
and mobile by light, strong, rigid construction of aluminum profiles.
various vacuum devices - vacuum-, power- and airflow regulations small
internal volumes therefore fast build up of the vacuum (electric/pneumatic)
no heat emission (pneumatic) spark-proof
interior and exterior
solvent resisted solvent
collecting system (in quantity)
low noise level and easy to clean multifunctional
use or just specific application
JEZET SUCTION and VACUUM TABLES SYSTEMS
MINI SUCTION TABLE TOPS (100 X 100 mm) to MULTIFUNCTIONAL VACUUM TABLE SYSTEMS totally
adjustable in height, angle and surface
The first JEZET SUCTION table systems from 1983 were mostly to use of hold-down low
pressure suction, for the spraying of deacidification-liquids on acid paper and little
restoration work. Later on with low pressure suction; medium pressure suction; vacuum
up till even high vacuum for all kind of purposes, treatments and actions like:
rinsing; washing; bleaching; deacidifying; disinfecting; moistening-treatments; humidifications;
tape -or stain removal; vellum flatting-, supplying-treatments; lining; hot-lining;
sizing; strengthen; straining; stretching; paper splitting; spot casting; spot fibering.etc.
Making use of all sorts of treatment liquids, solvents; fumes, glues, waxes and pastes.
To do special treatments on different materials like: PAPER, TEXTILE, VELLUM, LEATHER,
OILPAINTING etc.
The treatments can be divided on to 3 different surface sizes and 3 vacuum generations
each with its special qualities as: usability, capability, adaptability, performance
and advantages.
